|
EastManufacturing MMX
STANDARD SPECIFICATIONS |
|
|
Main
beams |
28-3/4"
deep 6061-T6 full length extruded aluminum beams with "double-T"
design and no vertical welds or splices |
|
|
Neck/F.W.H. |
12-1/2"
deep with smooth taper through transition -- 49"FWH |
|
|
Rear
deck height |
54-1/2"
rear deck height -- beam tapers to 20" at rear on 49' length |
|
|
Crossmembers |
Exclusive
tubular 6061-T6 aluminum extrusions spaced 22" apart. They
are welder on the front and rear sides to the inside of the
main beams. |
|
|
Floor |
1-1/2"
thick, multi-hollow, skid resistant extrusions with internal
ribs on 1" centers. The floor plank to the main beam connections
are welded full length. Three 5-1/2" wide apitong nailers
are standard. |
|
|
Side
rail assembly |
Patented
Securetight system that includes integrated winch track and
locking tie-down track extruded into the side rail. All East's
cargo control items have been tested and certified to Canadian
Test Method 905, and will meet and/or exceed the NACSS. |
|
|
Winch
track |
Standard
-- both sides -- integrated into the side rail |
|
|
Tie-down
track |
Standard
-- locking track (3" increments) integrated into the side
rail |
|
|
Inside
tie-down track |
Optional
-- full length track adjustment to the outboard edge of the
top main rail |
|
|
Locking
tie-down |
Optional. |
|
|
Winch
clips |
Optional. |
|
|
Pockets/spools |
The
stake pockets have a 1-3/4" x 2-7/8" inside dimension
and are on 24" centers. Single spool spacers are located
between the pockets. |
|
|
Nose
assembly |
7"
wide nose extrusion with a sloped pick-up ramp and squared corners. |
|
|
Upper
coupler |
30"
or 36" king pin setting in a 5/16" steel 5th wheel
plate. |
|
|
Rear
assembly |
Fully
enclosed light housing with an internal rear deck support. Each
side has three (3) stop, tail and turn lights, as well as outboard
mounted dock bumpers. |
|
|
Rear
bumper |
Two
(2) 5-1/2" hollow, extruded, vertical members with a 4-1/2"
x 5-1/4" horizontal bumper with integrated non-skid edges. |
|
|
Electrical
Lights & Wiring |
12
volt, 7-way D.O.T. connector. The wiring harness is sealed and
includes molded rubber plugs. Five (5) sealed beam marker lights
per side are standard. Mid-mount turn signals are also standard. |
|
|
Hubs |
10
stud steel, piloted hub with outboard mounted cast drum. |
|
|
Wheels |
8.25"
x 24.5" piloted steel disc |
|
|
Tires |
11
R x 24.5" Bridgestone R-196 (14) ply radials. |
|
|
Brakes |
Quick
change, 16-1/2" x 7" extended life, s-cam, with no
dustshields. Auto slacks are standard. |
|
|
ABS
system |
Wabco
4 sensor / 2 modulator system on widespreads. |
|
|
Axles |
5"
round, tapered bearing spindle configuration. Axles are integral
part of suspension. |
|
|
Suspension |
Hendrickson
AA-250-14/14 on a 10' 1" spread. A mylar sheet is used
between the aluminum and steel connections, where the suspension
is huck bolted to the frame. |
|
|
Mudflaps |
Silver
anti-sail, anit-spray mounted on rear light panel. |
|
|
Landing
gear |
2-speed
with self-leveling shoes. The crank handle is on the curbside. |
|
|
Tire
carrier |
Optional. |
|
|
Paint |
Silver
enamel standard -- other optional colors available. |
|
|
Finish |
Steel
components are treated to retard rust and are painted with one
step modified urethane in a choice of four standard colors.
All steel and aluminum connections are insulated to deter the
onset of galvanic corrosion. All aluminum components are natural
finish. |
|
|
Reflective
tape |
Choice
of eight (8) available colors. |
|
|
NOTE:
East Manufacturing Corporation reserves the right to substitute
components without notice, unless specified on the order. Prices
and specifications are subject to change without notice. Federal,
state and local taxes are not included. Copyright Jan. 2001.
All rights reserved. Specifications included patented items
and patent pending. |
|
Tel: (509) 535-0291
Tel: (509) 535-0291